Accessories

Stainless Steel Pressure Relief Valve

The VERSA stainless steel Pressure Relief Valve is designed to withstand challenging conditions in pneumatic applications. The relief pressures are factory set and tested in 5 psi (0.34 bar) increments to meet your application requirements.

Product Features

• Constructed of SAE 316 stainless steel conforming to NACE standard MR-01-75 suitable for direct exposure to sour environments
• FKM o-ring seals perform reliably with exposure to hydrocarbons or highly corrosive fluids over a broad temperature range: equivalent to Viton®, Fluorel®

100% Leak Tested • 10-Year Warranty

Stainless Steel Shuttle Valve

The VERSA Shuttle Valves are constructed of 316 stainless steel with resilient seals providing tight shut-off. Shuttle Valves are 3/2 valves primarily used to charge and discharge a pressure line or chamber from two – or more – sources. When a pressure signal enters the port blocked by the shuttle, it will cause the shuttle to shift toward the high-pressure port.

Product Features

• Constructed of SAE 316L marine grade stainless steel conforming to NACE standard MR-01-75 suitable for direct exposure to sour environments
• FKM o-ring seals perform reliably with exposure to hydrocarbons or highly corrosive fluids over a broad temperature range: equivalent to Viton®, Fluorel®

100% Leak Tested • 10-Year Warranty

Stainless Steel Pneumatic Gauge

The VERSA Pressure Gauge includes a stainless steel case with a 1/4 inch NPT connection (male thread) center back. Available in 2” and 2.5” diameters. Option for glycerine filled.

Product Features

• Constructed of SAE 316 stainless steel conforming to NACE standard MR-01-75 suitable for direct exposure to sour environments

100% Leak Tested • 10-Year Warranty

Stainless Steel Block & Bleed Valve

The VERSA Block and Bleed valve is a traditional isolation valve. It is designed to first isolate and then vent downstream pressure during gauge changes.

Product Features

• Constructed of SAE 316 stainless steel conforming to NACE standard MR-01-75 suitable for direct exposure to sour environments
• FKM o-ring seals perform reliably with exposure to hydrocarbons or highly corrosive fluids over a broad temperature range: equivalent to Viton®, Fluorel®

100% Leak Tested • 10-Year Warranty

Brass Bleed Control Valve

The VERSA brass Bleed Control Valves provide economical, effective flow control in pneumatic applications. The Bleed Control Valve screws into the exhaust port of any VERSA directional control valve to offer built-in cylinder speed control.

Product Features

• Constructed of forged brass with electroless nickel plating for increased wear resistance, hardness and corrosion protection. Long-lasting performance in the most demanding conditions

100% Leak Tested • 10-Year Warranty

Stainless Steel Bleed Control Valve

The VERSA stainless steel Bleed Control Valves provide economical, effective flow control in pneumatic applications. They can be screwed into the exhaust port of any VERSA directional control valve to offer “built-in” cylinder speed control.

Product Features

• Constructed of SAE 316L marine grade stainless steel conforming to NACE standard MR-01-75 suitable for direct exposure to sour environments

100% Leak Tested • 10-Year Warranty

Aluminum Dust Excluder

The VERSA aluminum Dust Excluder protects against dirt, dust, moisture, and insects entering the valve through the exhaust port without obstructing the flow. The Dust Excluder is based on a flexible seal resting on a large-diameter seat. The design provides a tightly closed exhaust port, low breakaway pressure, large flow capacity, and self-cleaning action. It is installed by threading into the exhaust port of a directional control valve.

Product Features

• Constructed of hard yet lightweight, corrosion-resistant anodized aluminum
• Buna-N/nitrile rubber o-ring seals perform reliably with oil, fuel, and other chemicals over broad temperature range

100% Leak Tested • 10-Year Warranty

Brass Bleed Control Valve

The VERSA brass Bleed Control Valves provide economical, effective flow control in pneumatic applications. The Bleed Control Valve screws into the exhaust port of any VERSA directional control valve to offer built-in cylinder speed control.

Product Features

• Constructed of forged brass with electroless nickel plating for increased wear resistance, hardness and corrosion protection. Long-lasting performance in the most demanding conditions

100% Leak Tested • 10-Year Warranty

¾” Hardware Kit. C.61

1” Hardware Kit. C.61